ChordRoot
Menu

Banjo tunings

A 5-string banjo has a short 5th string that's tuned high, so it can ring as a drone above the melody. Open G is the reference tuning, and strumming its open strings gives you a G chord. Double C retunes 2 of the longer strings so that open C and G notes ring under a tune in C.

Not every banjo chart names its tuning, and the same shape gives different notes in double C, so check which one it uses first. The number after each note name is its octave, and D3 sounds an octave below D4.

The 2 banjo tunings

Each line lists the open strings from the 5th string to the 1st, with a note on what that tuning does to the sound. Open G is the reference. Double C changes the 4th and 2nd strings and leaves the short 5th string at G.

How the banjo tunings compare

You'll find 48 charted chords for each tuning. We count a chord as easy when it has no barre, uses 3 fingers or fewer and stays within frets 1 to 4. Open G comes out ahead with 28, and double C has 25.

TuningNotesFrom standardEasy chords
Open GG D G B Dthe reference28 of 48
Double CG C G C Dlow D down a whole step to C and B up a half step to C25 of 48

Chords with 2 fingers or fewer in each banjo tuning

You can play between 11 and 15 chords with 2 fingers or fewer, depending on the tuning. In these names m means minor, 7 means a dominant seventh, and 5 means a chord of just the root and the 5th.

TuningChord countChord names
Open G11C5 C#5 D5 Em E7 E5 G Gm G7 G5 Bm
Double C15C Cm C7 C5 F Fm F5 G G5 Ab Ab5 Am A5 Bb5 B5

How to tune a banjo

Use a chromatic tuner and follow the string numbers in order, setting each open pitch and then checking the others again once they've settled, since a string you've just moved will often pull the others slightly out. Octaves matter here. A tuner that shows them helps, because G3 and G4 share a letter name but sound an octave apart.

The short 5th string sits next to the 4th but sounds higher than every other string, so you should check string numbers as well as note letters. A shape such as 02012 lists the frets from the 5th string to the 1st. A 0 means an open string.

Open G tuning

The open strings are G4, D3, G3, B3 and D4, and strummed together they sound G (G major), with the notes G, B and D. The short 5th string supplies a high G drone above the bass and melody range. Every open string belongs to the G chord.

Start a slow roll by picking strings 4, 3 and 2, then let the 5th string ring between those lower notes. The drone stays on G while a melody moves through G major, so you may hear clashes when a tune's home note changes.

Open pitchesG4, D3, G3, B3 and D4
Open chordG
Chord notesG, B and D
C major shape02012

Retune each string for open G

StringFromTarget pitchChange
short 5th stringAny pitchG4Set
4th stringAny pitchD3Set
3rd stringAny pitchG3Set
2nd stringAny pitchB3Set
1st stringAny pitchD4Set

Then play the C shape, 02012, by fretting the 4th string at fret 2, the 2nd string at fret 1 and the 1st string at fret 2, with strings 5 and 3 open, and listen for a clean ring from all 5 strings. In the C shape the open 5th string G is the fifth of the chord, so you can let it ring above the fretted notes.

Stay with open G when you want a high G drone to ring over chord changes, and compare double C when a tune centers on C. Most common chord diagrams assume this setup.

Double C tuning

Strummed open, G4, C3, G3, C4 and D4 form Gsus4 (G suspended 4th), with the notes G, C and D. Double C puts C on the 4th and 2nd strings while the short 5th string stays at G. The 3rd remains G.

Leave the short 5th, the 3rd and the 1st strings alone while you retune the 2 middle strings. Then recheck all 5. The open C and G notes give you drones that usually fit a melody in C.

Open pitchesG4, C3, G3, C4 and D4
Open chordGsus4
Chord notesG, C and D
C major shape00002

Retune each string for double C

StringFromTarget pitchChange
short 5th stringG4G4unchanged
4th stringD3C3down a whole step
3rd stringG3G3unchanged
2nd stringB3C4up a half step
1st stringD4D4unchanged

Then play the C shape, 00002, by fretting the 1st string at fret 2, with strings 5, 4, 3 and 2 open, and listen for a clean ring from all 5 strings. Fretting the 1st string at fret 2 turns its D into E, the major third of C, so play the open strings first and then add that note.

Double C suits tunes whose home note is C, with open C and G notes ringing under the melody. Before you put the banjo away, note which tuning it's in, because open G needs D3 on the 4th string and B3 on the 2nd.

Which banjo tuning to start with

Start with open G tuning. Most common chord diagrams assume it, and it has the most easy chords of the 2, 28 of 48. Switch to double C when a tune's home note is C and you'd like open C and G notes ringing under the melody.