ChordRoot
Menu

Tap BPM and tap tempo counter

Tap the button, or press the space bar, in time with the beat. This tap BPM counter shows the tempo from your second tap and keeps averaging as you go.

-- BPM

Tap twice or more to see the tempo.

Half time -- BPM, double time -- BPM

Space bar works too. A pause of 3 seconds starts a new count.

How to use the tap BPM counter

You only need a steady beat to follow, either from a song you know or from your own playing.

  1. Find the beat you'd tap your foot to, and count it out loud for a bar or two.
  2. Tap the big button, or press the space bar, once on every beat. Four taps give a rough tempo, and 8 or more settle it.
  3. Read the BPM beside or below the button. Press Reset, or wait 3 seconds, and your next tap starts a new count.

Start counting from the first beat of a bar if you can, because that keeps your taps in a steady pattern. The counter doesn't need to know where the bar starts, and it never listens to anything, so it only reads the taps you make.

Worked example, 8 taps at 120 BPM

Say you tap 8 times and each tap lands 500 milliseconds after the one before.

That makes 7 gaps of 500 milliseconds, and 60,000 divided by 500 is 120, so the counter shows 120 BPM. Half time reads 60 and double time reads 240. Tap a little slower, at 600 milliseconds, and you'd see 100 BPM.

The table shows what other steady gaps give. A slower gap means a lower BPM, and halving the gap doubles it.

Gap between tapsBPM
300 ms200
400 ms150
500 ms120
600 ms100
750 ms80
1000 ms60

Beat lengths for a delay or tremolo

Once you know the BPM, this table gives the length of common note values in milliseconds, which is what many delay and tremolo settings ask for.

The dotted eighth is three quarters of a beat, and an eighth-note triplet is a third of one. Round to the nearest millisecond if your pedal has no finer setting.

Note lengths in milliseconds at each BPM
BPMQuarter noteDotted eighthEighthEighth tripletSixteenth
601000750500333250
80750563375250188
100600450300200150
120500375250167125
140429321214143107
16037528118812594

Why one BPM is only an estimate

Live players speed up and slow down a little, and some styles lean on it on purpose. Musicians call that rubato. Your taps follow the drift, so the number is an average of your latest taps and not a promise about every bar.

If it jumps around, tap along to a longer stretch of the song and watch where it settles. A tempo that feels too fast when you record may also be one you chose by feel for a single section, so check it against the whole song before you rely on it.

Questions about tap tempo

How do I find the BPM of a song by tapping?

Tap the button once on every beat for 8 taps or more and read the BPM it shows. The counter averages the time between your taps, so a slip early on matters less as you keep going.

How many taps do I need?

Two taps give a first reading, and 8 or more taps even out small slips. Only your latest 16 taps count, so the number follows you if the tempo drifts.

Why does the BPM change while I tap?

Your taps change a little from beat to beat, and the song may speed up or slow down. The number settles once you tap steadily, so keep your taps even and watch it for a few bars.

Is BPM the same as the time signature?

No. BPM counts how many beats fit in a minute, while a time signature such as 4/4 or 3/4 says how many beats sit in each bar. You tap the beat in both cases.

More tools

Each of these opens in the same page layout, so you can move from one job to the next without starting over.